LPWS Basic Knowledge Practice Exam

These questions are part of the practice quiz. Start practicing

• What is the function of the ballast?
• Which option correctly states the two radar capabilities?
• Which constitutes effective team communication?
• Which unit is used to express the muzzle velocity of the M940 round?
• Which maintenance approach uses condition data to anticipate failures and schedule repairs?
• What is the search sector for the LPWSs Search Radar?
• Troubleshooting actions require whose approval?
• What does ELX stand for?
• From what sources can we get power?
• What should you do if a fire alarm sounds in LPWS?
• How should chemical waste be disposed of in LPWS?
• What is a lock-out/Tag-out device?
• Sensor Registration ensures that reported track positions are correct and correlate with reporting sources.
• What is the initial action to take upon receiving a fault?
• What is the purpose of a control chart in LPWS?
• Which statement best describes the difference between a hazard and a risk?
• What is document control?
• Which configuration describes the mount’s power generation setup?
• WP 34 is a procedure conducted to perform what?
• Which statement best describes the purpose of an SOP?
• What is the round size?
• Which statement describes the relationship between redundancy and safety?
• How should incident reporting be documented?
• When disposing chemical waste, which practice is essential?
• Which technique reduces back injury when lifting a load?
• Which statement about PRCS is true?
• Which maintenance approach is based on monitoring equipment condition to schedule maintenance before failure?
• Which item is not typically included in a basic first aid kit for LPWS?
• What does Sensor Registration produce for the LPWS in relation to sensors and the EOC?
• What code can change the ammo count within the system?
• Identify a noncomponent option that is NOT part of the I2N.
• What does PAC stand for?
• What does PRCS stand for?
• What additional measures are required in chemical hygiene besides PPE?
• What window do you open in WINPASS?
• What should be included in a basic first aid kit in LPWS?
• What is the muzzle velocity of the M940 round?
• How often is the WADS supposed to change over?
• What is the purpose of a permit system in LPWS?
• What does PSOT 14 do?
• How many radars are there?
• How many SOTS are run for dailies?
• What must be off before you go to stand by?
• Which standard provides a quality management framework for consistent products and continuous improvement in LPWS?
• What are the radars?
• Which statement about Safety Data Sheets (SDS) is correct?
• ISO 9001 relates to LPWS by providing a quality management framework to ensure what?
• What is the designation of the round?
• What frequency are the generators set to?
• What does data integrity mean and why is it critical?
• What code do you run to get back power?
• What is the risk of noise exposure and how can it be mitigated?
• The LPWS defended altitude maximum is what value?
• Who is the FLIR picture for?
• How should you respond to a chemical spill if you are trained to handle it?
• How is 'critical equipment' defined in maintenance?
• Which combination matches the radar's search sector?
• What connects The FLIR/ballast to the mount?
• Which of the following is NOT typically included in a daily start-up checklist for LPWS?
• PSOT 14 is designed to test which gun parameter?
• Which of the following generator frequency values is used in the system?
• How should waste be segregated?
• Which elements are essential when reading a blueprint in LPWS?
• What two methods are used for destroying classified equipment?
• Which statement correctly differentiates preventive and predictive maintenance?
• Which of the following describes a component of the I2N?
• What is the TM for the system?
• How many components are in the I2N?
• The FLIR image is intended for which authority to help prevent fratricide?
• Why is cybersecurity important in LPWS?
• What is change control?
• Which elevation value defines the radar's search sector?
• How should sensitive or perishable documents be handled?
• In a startup sequence, which option lists the correct order?
• What is the purpose of documenting alarm events and performing root-cause investigations?
• What is the purpose of maintaining equipment labels over time?
• How many barrels does the gun have?
• Why is load bank testing important for LPWS generators?
• Which component is essential for handling sensitive documents to track changes over time?
• What information does an SDS provide?
• Which list correctly identifies the four components of the I2N?
• Which three items must be checked or serviced during daily maintenance?
• What is the cage called?
• How is a confined space defined in LPWS?
• The LPWS defended area is what distance?
• Which option lists the chiller coolant solution?
• Which component is housed in the electronics enclosure?
• Which PPE is typically required when handling chemicals in LPWS?
• What goes under the FLIR?
• Which action best verifies that a control measure is effective?
• EOSS stands for which term?
• What CB is pulled to stop mount movement?
• Which statement accurately describes the M940 round?
• WP 34 is conducted to perform what?
• Which action best supports maintaining energy isolation during maintenance?
• What solution is used in the chiller?
• Which device is used to stop rounds entering the firing path?
• What does the gun sit on?
• Which sequence correctly represents the steps in a basic risk assessment?
• After documenting an incident, what is the next best action?
• What is the difference between calibration and validation?
• Within WINPASS, which window is used for terminal-type access?
• ___________ is conducted to calibrate the mount azimuth and alignment.
• Which statement best describes how traceability supports product safety?
• What does DNES stand for?
• The fire rate equals 4500 rounds per minute. Which of the following is equivalent in rounds per second?
• Which PSOT is run before a PAC-Fire?
• Which two components' combined function is to separate and stabilize the barrels?
• Why is housekeeping important in a workshop?
• What code pulls detailed data for SOTs?
• Which procedure is conducted to calibrate the mount azimuth and alignment?
• Sensor Registration is an important process that calibrates radars and Phalanx Weapon Systems to ensure that reported track positions are correct and correlate with all reporting sources. Which statement best reflects this?
• The LPWS defended wall altitude maximum is 900 meters, which corresponds to which option?
• What is the minimum number of legs that must be flown to complete sensor registration?
• The term 'Generator Set' refers to which assembly?
• Alarm management involves which activities?
• What is the nomenclature of the gun?
• Document control encompasses which of the following functions?
• How is the system cooled?
• SOTs 1-7 refer to which subsystem?
• What generators do we use?
• Which of the following is NOT a component of the I2N?
• What is the name of the crane used to lift the EOSS?
• What does GHS stand for and why is it important?
• What maintenance step helps prevent damage from wet-stacking in LPWS generators?
• What are the elevation limits?
• The ballast serves as a counterweight for FLIR and EOSS assembly.
• What does FLIR stand for?
• What does a chemical hygiene program involve?
• Why is redundancy important in safety systems?
• How is a quality defect typically classified in LPWS?
• How does traceability support product safety?
• What is ergonomics and why is it important in LPWS?
• What are the correct steps in a basic risk assessment?
• In LPWS, what best defines a near miss?
• What is the nomenclature for the round?
• What is Root Cause Analysis and a common method?
• What is a basic electrical safety practice?
• What three actions are performed prior to running a PSOT?
• Which statement best describes a near miss?
• How is the mount powered?
• How should frequently used equipment be maintained?
• Before performing a PAC-Fire, which PSOT is typically run?
• Why is labeling important when segregating waste?
• What computer program do you start?
• PSOT 22 is necessary to conduct what type of engagements?
• Who must approve troubleshooting actions?
• Which component is used to lift the EOSS?
• Which of the following expresses the elevation limits most accurately?
• Which item is essential for daily maintenance checks on the LPWS control panel?
• What is energy isolation in maintenance?
• Which of the following best describes the purpose of a permit system in LPWS?
• What does SOT stand for?
• What tool is used to stop the rounds from moving into the firing path?
• On what basis should PPE be selected in LPWS?
• What is the fire rate?
• What is the exact code to pull detailed data for SOTs?
• Which statement best describes the system's mode of operation with oversight?
• Which of the following describes a capability of the PPI display?
• Which azimuth value defines the radar's search sector?
• The acronym DNES refers to which sector?
• How many rounds can the drum hold?
• Which component serves to stabilize the electro-optical payload?
• What test fire is run after a PAC-fire?
• What does GD&T stand for in blueprint reading?
• How should supplier quality be evaluated in LPWS?
• How is the system operated?
• Which of the following is a described capability of the PRCS in relation to LPWS?
• Which display shows real-time LPWS radar feedback, known aircraft, and confirmed RAM data?
• Which statement about ballast is true?
• Which option describes the generator setup used to power the mount?
• How many bars does the sensor radar have?
• What is this type of cooling system called?
• What component is commonly referred to as the 'brain' of the system?
• Which list includes only the four I2N components?
• Which circuit breaker is pulled to stop mount movement?
• Which practice supports maintaining safety and quality when updating equipment?
• What is the maximum range of the LPWS?
• What is the end product of sensor registration?
• What is the nickname for the protective enclosure in this setup?
• What is the purpose of lockout/tagout (LOTO) in LPWS?
• What wattage is the generator typically set to?
• What is the temperature range of the chiller?
• What is the brain of the system?
• What does traceability mean in LPWS?
• Which of the following is a component of the I2N?
• Which two components are used to separate and stabilize the barrels?
• When is a permit-to-work required?
• How should equipment be labeled?
• Which statement about the search sector is false?
• Which items should be included in a daily start-up checklist for LPWS?
• Which sequence describes a typical startup sequence?
• Which statement best describes lockout/tagout (LOTO) in an industrial setting?
• Which of the following is true about the generator wattage setting mentioned?